Skip to content
HYPERPCB

USB‑C design review checklist: CC wiring and power‑path management

Published 2026-11-11

For a sink‑only USB‑C, place two 5.1 kΩ (Rd, ±20%) pulldowns from CC1 and CC2 to GND within 2 mm of the receptacle; do not omit either CC pin.

CC wiring — what values and where to place?

Sink role: use 5.1 kΩ on both CC pins. Keep each CC trace short (<10–15 mm), route as single‑ended with a solid return under it, and drop at least two stitching vias to the ground plane within 1–2 mm of each Rd pad to keep the return impedance low.

Source role: advertise current with Rp referenced to 5 V. Typical discrete values are ≈56 kΩ (Default USB current), ≈22 kΩ (1.5 A), ≈10 kΩ (3 A). Dual‑role and PD designs should use a USB‑C/PD controller that switches Rp/Rd per USB Type‑C and USB PD specs; do not hard‑wire mixed roles.

Dead‑battery and ground reference — what changes?

Attach must work with the system unpowered. Tie the two 5.1 kΩ Rd parts directly to the system ground net that is present at all times (before any load switch or ideal‑diode FETs). Avoid placing Rd on a power‑gated ground island. A practical check: with the main rail off, the CC pin voltage from a 5 V source should sit in the sink‑attached window (hundreds of millivolts, not open‑circuit or ~5 V). Keep leakage to VBUS below a few microamps; CC should never be tied to any rail through ESD diodes.

VCONN sourcing limits and protection

Only drive VCONN on the unused CC pin after you detect an e‑marked cable. Limit VCONN to 5 V with over‑current protection set around 200–250 mA (USB‑C allows up to 1 W on VCONN). Place a low‑capacitance ESD protector at the receptacle end, and keep the VCONN run short and off noisy switcher regions.

Power‑path topologies and FET orientation

5 V sink up to 3 A: receptacle VBUS → TVS diode → back‑to‑back N‑MOSFETs (reverse blocking) → current‑limited switch/e‑fuse → bulk input cap → buck/LDO. Size FETs for conduction loss: at 3 A and 20 mΩ per FET, each FET dissipates ≈0.18 W; provide copper for heat spreading.

PD sink (5–20 V): use a TVS with ~24 V standoff and an e‑fuse/OVP rated for 20 V+. Choose a buck regulator with ≥24–30 V abs max. Ensure the back‑to‑back FET body diodes face to prevent back‑drive into VBUS on detach.

Dual‑role power: implement two ideal‑diode paths (VBUS→system and system 5 V→VBUS) with hardware or firmware interlock so both can’t conduct simultaneously. If supporting Fast Role Swap, verify load‑rail droop during switchover and adjust bulk capacitance and FET gate drivers accordingly.

High‑speed and ESD placement — what targets?

USB 2.0 D+/D−: 90 Ω differential, 45 Ω single‑ended. Match the pair within a few mils, keep stubs minimal, and maintain a continuous return plane. Place the ESD array immediately behind the receptacle and route through it first.

USB 3.x SuperSpeed: 85 Ω differential. Minimize via count; when vias are unavoidable, use tight antipads, short back‑drills if available, and keep transitions symmetric. Separate SuperSpeed pairs from VBUS copper and switching nodes to reduce mode conversion.

SBU/CC: protect with low‑capacitance ESD (sub‑1 pF for high‑speed‑adjacent nets). Route SBU away from buck switch nodes and magnetic components.

Typical ratings to confirm during part selection

VBUS TVS: for 5 V‑only sinks, 5–6 V standoff; for PD up to 20 V, ~24 V standoff with low dynamic resistance. ESD arrays: IEC 61000‑4‑2 ±8 kV contact on connectors; choose low‑C parts on high‑speed lines. Bulk input capacitance: 10–22 µF X5R/X7R near the power‑path output, with regulator soft‑start to control inrush.

Bring‑up tests — what should you measure?

  • Attach/detach at 0–3 A load: no back‑drive to VBUS after detach; no overshoot at the system rail.
  • Short‑circuit: short VBUS to GND at the receptacle; verify e‑fuse current limit, OVP trip, and auto‑retry per design.
  • Overvoltage: apply 6 V to a 5 V‑only design and ~22 V to a PD design; confirm shutdown thresholds and FET reverse blocking.
  • Thermal: run 3 A continuous; check MOSFET case and copper temperatures vs. calculated I²R losses.
  • Signal integrity: USB 2.0 HS eye at the connector; confirm ESD/chokes don’t violate masks.

Common mistakes and quick fixes

Only one Rd fitted: add the second 5.1 kΩ to the other CC pin. ESD arrays far from the receptacle: move them to within a few millimeters and route through the device. Sense resistor not Kelvin‑routed: split measurement traces before entering high‑current copper. Back‑to‑back FETs reversed: flip the pair so body diodes oppose each other toward the system rail.

Fabrication and compliance notes for production PCBs

Call out controlled impedance for 90 Ω (USB 2.0) and 85 Ω (SuperSpeed) pairs in your fab notes, and specify the target stack‑up. Boards can be built and inspected to IPC Class 2 or IPC Class 3 acceptance criteria, with RoHS and REACH compliance supported. HyperPCB operates an ISO 9001:2015 certified quality management system (certificate no. CN‑2023‑Q1156, issued by SGS, valid until June 2027). Quotes are returned within 24 hours and DFM feedback within 1 business day.

Send your USB‑C Gerbers and stack‑up; get a 24‑hour quote and 1‑business‑day DFM feedback. — Get a quote